Custom guns

BrothersInArms

Supporting Vendor
Here's a couple we finished up this week. I'll update this thread with pics of our builds as we finish them.

Tricked out Bushmaster. Yeah, the stock is ugly... it'll have a new one on there tomorrow.

DSCF5783.jpg


2.5-10 power, dual illuminated optics with the iron sights at a 45*
DSCF5784.jpg


A little mill work on the rail system.
DSCF5785.jpg


Custom brake.
DSCF5786.jpg




We went a little wild on this one lol. Competition Glock 24: slide lightened, custom compensator, Lone Wolf extended/threaded barrel, improved guide rod and spring system, all internals are either aftermarket and/or reworked by us, flared mag well, grip reduction and stippling, 2 tone grey and black.

DSCF5787.jpg


DSCF5788.jpg


DSCF5789.jpg


DSCF5790.jpg
 

Arckadian

Active member
I like the glock... how much did it cost to do all that modification and how long did it take?.... my next question will hurt some, but how much does something like that cost?
 

BrothersInArms

Supporting Vendor
I like the glock... how much did it cost to do all that modification and how long did it take?.... my next question will hurt some, but how much does something like that cost?

Thanks! shes a SWEET shooter. I couldn't even tell you how many hours I spent in front of the mill lightening the slide and fabricating the compensator. I started with a rough "blueprint" in my head and started putting it down in steel, always takes a little more time. About 2 hours on the grip reduction and stippling. About 2 hours on the action and trigger job, and slide to frame fit. Several hours in duracoat and masking. It goes on and on. All told a few days work. We have it for sale at $1800 with the compensated match barrel and factory barrel, 2-15rd mags, and a 31rd mag.
 

BrothersInArms

Supporting Vendor
Does your shop have normal store hours or is it by appointment only?


My Saiga needs your help.

We have the show room open from 10am - 7pm, Monday - Friday. We are typically here working earlier and often later, and on most weekends as well. If it's after hours or a weekend just give us a call first and we can make sure that we are here. (830)-399-2281


We're located at:
2892 hwy 71 w
Cedar Creek, TX.
78612
 

Dr_Pain

Full Access Member
Love that we have vendors on the forum that don't mind sharing the gun porn :)

Great looking weapons! Hope you keep us informed of any sales, inventory reductions etc...

BTW we need some ammo vendors. Would love to get in some group buy for large quantities (zombie stock is getting low!)
 

BrothersInArms

Supporting Vendor
Love that we have vendors on the forum that don't mind sharing the gun porn :)

Great looking weapons! Hope you keep us informed of any sales, inventory reductions etc...

BTW we need some ammo vendors. Would love to get in some group buy for large quantities (zombie stock is getting low!)

Thank you! We're working on the ammo.
 

BrothersInArms

Supporting Vendor
Mossberg 500- Spec Ops Gen 2 stock, ATI forend, shortened barrel, permanently attached custom brake, reworked action, 2 tone grey/black duracoat.

DSCF5798.jpg


DSCF5799.jpg


DSCF5800.jpg
 

BrothersInArms

Supporting Vendor
Customer ordered Saiga 7.62x39-- Receiver conversion, threaded barrel, polished bolt and bolt carrier, ACE stock with push button side folder, Damage industries forend, resurfaced FCG, bullet guide, in house made charging handle, trigger guard and selector lever.


DSCF5807.jpg


DSCF5808.jpg


DSCF5809.jpg
 

BrothersInArms

Supporting Vendor
This is our "basic" Saiga 12. Receiver conversion done the right way... no plastic caps or bolt on crap... all riveted and welded. We reworked the gas system so it will run low brass/light loads. Resurfaced the FCG for smooth function. Fixed AK stock, and a Tapco tri rail forearm. Duracoated OD green.


DSCF5811.jpg


DSCF5812.jpg
 

BrothersInArms

Supporting Vendor
Pretty Basic Saiga 7.62. We've got one in the works that's a bit more wild... should be finished tomorrow:leghump:

Converted, threaded barrel with Phantom flash hider, fixed DPH skeleton stock, UTG quad rail.


DSCF5813.jpg


DSCF5814.jpg


DSCF5815.jpg
 

RangerDanger

Full Access Member
This is our "basic" Saiga 12. Receiver conversion done the right way... no plastic caps or bolt on crap... all riveted and welded. We reworked the gas system so it will run low brass/light loads. Resurfaced the FCG for smooth function. Fixed AK stock, and a Tapco tri rail forearm. Duracoated OD green.

How much for a conversion like this? I've already had the gas system reworked so I'm fine there. PM if your like
 

BrothersInArms

Supporting Vendor
How much for a conversion like this? I've already had the gas system reworked so I'm fine there. PM if your like

The conversion is $300. That includes a new G2 fire control group(FCG), relocating that FCG, welding and resurfacing the holes left after the conversion, a Hogue grip, our custon trigger guard, and a duracoat finish in your choice of color.

Most shops use plastic plugs instead of weld filling the holes, use the stock flimsy trigger guard, and don't refinish the gun... for the same amount of money.

Stock, forearm, etc are cost plus 10% to cover shipping. No charge for installation.

Let me know

Brad
 

RangerDanger

Full Access Member
The conversion is $300. That includes a new G2 fire control group(FCG), relocating that FCG, welding and resurfacing the holes left after the conversion, a Hogue grip, our custon trigger guard, and a duracoat finish in your choice of color.

Most shops use plastic plugs instead of weld filling the holes, use the stock flimsy trigger guard, and don't refinish the gun... for the same amount of money.

Stock, forearm, etc are cost plus 10% to cover shipping. No charge for installation.

Let me know

Brad

Less than what I thought. I have a friend in your area so hopefully I can get the gun to him when he's in Houston to avoid shipping. It'll be a few months but I'm definitely interested
 

Members online

No members online now.

Latest posts

Top